折叠式变体飞行器轨迹优化及控制分析

针对临近空间高超声速飞行器存在的问题，设计了一种折叠翼飞行器，可以通过折叠机翼来适应各种飞行状态，保持最优的气动特性。并针对临近空间滑翔式高超声速的特点，采用高斯伪谱法对固定翼飞行器和折叠翼飞行器的轨迹优化，通过将折叠翼飞行器与传统固定翼飞行器在射程能力、规避热流能力方面进行对比，提出了一种综合目标的轨迹优化思想。设计的折叠翼飞行器相比传统固定翼飞行器性能更加优越，更适合临近空间环境，提高了17.67%的航程，减少了热流率峰值的35.72%，并通过控制系统的设计和仿真加以验证，仿真结果表明变体飞行器机动能力相比固定翼飞行器有了显著的提高。     

Sliding mode control design for oblique wing aircraft in wing skewing process

When the wing of Oblique Wing Aircraft (OWA) is skewed, the center of gravity, inertia and aerodynamic characteristics of the aircraft all significantly change, causing an undesirable flight dynamic response, affecting the flying qualities, and even endangering the flight safety. In this study, the dynamic response of an OWA in the wing skewing process is simulated, showing that the three-axis movements of the OWA are highly coupled and present nonlinear characteristics during the wing skewing. As the roll control efficiency of the aileron decreases due to the shortened control arm in an oblique configuration, the all-moving horizontal tail is used for additional roll and the control allocation is performed based on minimum control energy. Given the properties of pitch-roll-yaw coupling and control input and state coupling, and the difficulty of establishing an accurate aerodynamic model in the wing skewing process due to unsteady aerodynamic force, a multi-loop sliding mode controller is formulated by the time-scale separation method. The closed-loop simulation results show that the asymmetric aerodynamics can be balanced and that the velocity and altitude of the aircraft maintain stable, which means that a smooth transition is obtained during the OWA’s wing skewing.     

弹片热机械疲劳试验方法研究及设计

针对弹片的热机械疲劳（TMF）试验要求，采用机械设计技术、机电技术、冷却技术、计算机技术和数据采集技术，提出了压力载荷和热载荷的加载方法，建立了2种载荷5个试验件的并联试验控制系统，并设计了弹片热机械疲劳试验器。试验结果表明:该系统能够同时模拟服役环境下弹片的压力载荷和热载荷。利用该试验系统进行了弹片的热机械疲劳试验，试验结果再现了弹片在服役状态下的失效模式。试验系统具有良好的重复度、较高的加载频率和加载精度。压力载荷最大相对误差为2.4%，绝对误差小于0.5N。温度载荷最大相对误差为3.55%，最大绝对误差为3.89℃。      

Flow separation control on swept wing with nanosecond pulse driven DBD plasma actuators

A 15° swept wing with dielectric barrier discharge plasma actuator is designed.Experimental study of flow separation control with nanosecond pulsed plasma actuation is performed at flow velocity up to 40 m/s. The effects of the actuation frequency and voltage on the aerodynamic performance of the swept wing are evaluated by the balanced force and pressure measurements in the wind tunnel. At last, the performances on separation flow control of the three types of actuators with plane and saw-toothed exposed electrodes are compared. The optimal actuation frequency for the flow separation control on the swept wing is detected, namely the reduced frequency is 0.775, which is different from 2-D airfoil separation control. There exists a threshold voltage for the low swept wing flow control. Before the threshold voltage, as the actuation voltage increases, the control effects become better. The maximum lift is increased by 23.1% with the drag decreased by 22.4% at 14°, compared with the base line. However, the best effects are obtained on actuator with plane exposed electrode in the low-speed experiment and the abilities of saw-toothed actuators are expected to be verified under high-speed conditions.     

三维数模随动下的机翼结构重量优化

目前,基于快速建模下的重量重心估算系统得到了快速发展。为了进一步提高结构重量估算精度,研究了如何在重量重心快速分析(WCGA)系统环境中构建优化模块。以机翼结构重量优化为例,提出优化流程,对优化模块功能进行分解,给出模型简化要求。以A320飞机机翼为例,对梁和长桁进行优化,结果显示,经过优化,有效减轻了结构重量,且相比于传统的减重优化设计方法,极大提高了计算效率。     

基于LQG/LTR的飞翼飞机阵风减缓系统研究

根据我国《运输类飞机适航标准》的要求,采用有理谱逼近的方法建立了Von Karman大气紊流的数值仿真模型;详细推导了多变量系统鲁棒性的衡量方法,给出了开环系统奇异值曲线形状与闭环系统鲁棒性的关系;针对飞翼飞机多操纵面的特点,将控制分配技术与LQG/LTR控制器结合在一起,同时兼顾了对飞机过载和翼根弯矩的减缓。仿真结果表明,所设计的控制系统在对飞机过载减缓的同时,也对机翼的翼根弯矩进行了有效的减缓。     

基于AFAS 软件的机翼壁板耐久性分析及试验验证

随着航空工业的发展,对机翼壁板耐久性分析的精确性及计算速度的要求日益提高,必须考虑从手工计算到程序计算的转变。飞机结构耐久性分析软件系统(AFAS)是为了满足飞机结构耐久性分析的工程实际使用要求而编制的。本文介绍采用该软件中包含的DFR方法计算程序对机翼壁板结构进行耐久性分析的过程,并进行试验验证,分析得到的机翼壁板结构具有95%置信度、95%可靠度的可靠性寿命与试验统计结果非常相近,证明AFAS是一个可以进行耐久性分析的快速准确的计算工具。     

机翼顶起设计解析

飞机全机顶起是飞机维护时必不可少的操作程序,其中机翼顶起是全机顶起的一个重要组成部分。机翼顶起设计包括两个方面内容,即顶垫设计和机翼千斤顶选型。顶垫设计与顶起点结构设计、机翼千斤顶选型是联合设计、相互影响的。     

折叠机翼变体飞机纵向操纵性与稳定性研究

针对一种飞翼布局折叠机翼变体飞机方案,建立了相应的研究模型,使用涡格估算方法计算出机翼折叠角度对全机纵向静稳定性的影响.利用飞机纵向小扰动运动方程,分别得到了机翼展开和折叠状态的长、短周期模态,并对其动稳定性进行了讨论.结合工程估算方法和风洞试验方法,计算出内段机翼折叠过程全机力矩系数、升降舵操纵导数以及升降舵配平偏角...     

可变体机翼多物理场分布式光纤集成测试技术

介绍了可变体机翼技术和可变体机翼多物理场光纤集成测试技术的研究现状.